Strip the speaker wire to about 3/8″ to 1/2″ length bare wire. To use spade connectors like these pictured, simply unscrew the binding post on the back of the amplifier or loudspeaker and place the fork end of the connector against the binding post shaft.
Click here to see mueller electric's binding posts.
How to connect speaker wire to binding post. But if your in the testing stages of building, i would use the ring terminals for now and then solder them before you button up the box. Such speaker wire connectors include bare wire, spade lug connectors, and pin connectors. Most loudspeaker and amplifier connectors accept multiple types of connections:
To get the best sound quality, it’s important to wire your speakers correctly. Binding posts accept bare wire and four different types of connectors: The wire will be soldered to the terminal.
Also, note which way you have connected up the wire in terms of polarity. To ensure your speakers function properly, make sure that the wire leading to the positive (red) binding post is also connected to the positive terminal of your receiver or amplifier. You will have to get to the inside of the speaker.
In fact, probably the best method if you never disconnect/reconnect. Connect the speaker wires to the speaker terminals on the rear of the a/v stereo receiver. As for the wires inside the speaker box.
Those are usually held in with a nut on the inside. In this instalment of kanto solutions, we'll show you just how easy it is to connect speaker wire to your speakers' binding posts, using both bare wire and b. Feed your solder to the inside of the binding post at the post/ wire interface.
Tighten hex nut down to make connection. Some of the speaker wires come in a tinned shape. For binding post terminals, loosen the red (positive) or black (negative) binding posts by turning.
For spring clip terminals, press down on the red (positive) or black (negative) clips and insert the speaker wire into the slot. Then hold your iron up against the outside of the binding post by the hole the wire is looped thru. How to use binding post connectors loosen hex nut and insert bare speaker wire through hole.
Insert each side into the exposed holes. They are able accommodate speaker wire connectors that require a clamping action in order to transfer a signal. Then tighten the outer shell of the binding post down to hold it.
You will have to unsolder a wire probably. Banana plugs are very convenient, but i have an affinity towards bare speaker wire. So, you don’t have to do that in cases of those speaker wires.
What is more important is that all connections are clean and secure. Pin connectors, spade connectors, banana plugs, and dual banana plugs. It is, in fact, easier, since you can hold the banana plug in your hand while doing it, and don’t have to bend behind your stereo or speakers.
Steps for connecting speaker wire to binding post terminals on subwoofers: As part of our fluance ultimate guide to home theater setup, we will walk you through how to connect your speakers using speaker wire and binding posts. Just use zip ties and tie the cables up to any brackets of the drivers or on the box braces that are inside the box.
Connect the other end of the speaker wire to your speakers Installing speaker wire onto banana plugs is very similar to connecting speaker wire to a binding post, as detailed above. Do not insert insulated section of wire into hole (you will not get a connection).
If you remove the binding strap and connect 1 wire (neg/pos) to the top posts and 1 wire (neg/pos) to the bottom posts and then connect both wires to the same pos/neg terminal on the amplifier/receiver, uyou are creating the same parallel connection the strap does but instead of on the speaker you are doing it at the receiver/amplifier. Twist the wire tightly by hand to keep the wire strands together. At your receiver or amplifier, connect the two cables to one pair of red and black output terminals for the left channel, and two speaker cables to the other pair of output terminals for the right channel.
As for technique, you should coat the wire and post with rosin flux prior. As long as you twist them properly and leave no strands hanging outside and get the whole thing fit in the binding post and screw it tightly its the best connection imho. Make sure enough portion of the metal wire is inserted on them.
It is possible that the terminal was molded or pressed into the plastic. When done, the solder joint should have a smooth fillet (proper wetting) and not be a big blob. Can't find what you are looking for on do it yourself diy binding post or have a question?
Remove the bridge plates or pins between the binding posts and connect the two sets of speaker wires to the amplifier (making sure to note the bass posts and the treble posts). Banana plugs are inserted into a hole in the back of the binding post. Insert each of the cables into the hole now this is the most crucial part on which the entire connection depends on.insert each of the cable openings to the relevant binding post holes.